loading

Leading wire forming machine manufacturer specializing in the development of welding technology.

How to Control Hook Geometry in CNC Extension Spring Forming

×
How to Control Hook Geometry in CNC Extension Spring Forming

Extension spring hook forming combines local bending with control of the spring body and the relationship between both ends. A spring may have a consistent coil diameter while its hooks face the wrong direction or do not fit the mounting pins. Separate these requirements on the drawing so that a body adjustment is not mistaken for a complete solution.

Define the hook in an unambiguous view

Specify the hook or loop type, clear opening, inside radius or diameter where required, end position and transition from the body. State the viewing direction for orientation and show how the two ends relate to each other. A front view without an end view may leave a three dimensional relationship unclear.

Identify the mounting interface. If a pin must pass through the opening, the relevant clearance differs from the outer size of the hook. Use drawing dimensions and a functional gauge where specified; do not infer fit from a photograph of a similar spring.

Keep body and hook controls separate

List body diameter, body length, coil count and winding direction separately from hook opening and end orientation. Identify whether overall length includes the hooks and how the spring is supported during measurement. For extension springs with an initial tension requirement, the specified force behavior also needs its own acceptance test.

The CNC spring coiling machine selection guide helps connect spring features to equipment selection. For the hook trial, request the complete spring with both ends formed. A stable body coil demonstrates only part of the required process.

Confirm the wire and processing route

Record material grade, diameter, supply condition and lot. Review required stress relief, coating or other finishing with the responsible process specialist. Inspect the spring at the stages needed to distinguish forming variation from changes introduced later.

Do not apply a general temperature or cycle to every spring material. The approved material and product specification must determine the route. If final acceptance occurs after treatment, preserve paired sample identities so before and after results refer to the same parts.

Review tool support and motion order

Map the actions that create the transition, form the hook and release the spring. Check support near the working bend, the clearance between successive tools and whether the body can rotate or distort during the sequence. A small shift at the transition can change the end orientation without an obvious change to the body.

Jinchun lists a multi axis camless spring forming machine as an option for spring and wire forms. Treat it as a candidate for tooling review. Ask the supplier to demonstrate your hook type and material; an axis count alone does not establish the ability to make every end geometry.

Inspect the transition as well as the opening

Check the region where the hook leaves the body for tool marks, unwanted flattening, local distortion and visible damage. Compare both ends rather than approving the easier end only. Follow the product inspection requirements for detecting defects; visual appearance alone cannot establish fatigue life.

Track when a mark appears in the sequence. A repeatable tool contact may need a different correction from damage during discharge or later handling. Retain labelled examples of accepted and rejected features to make setup reviews consistent.

Measure with a fixed locating method

Define how the body is held, which hook is the reference and whether the spring is unloaded or under a specified load. Flexible springs can give different readings if contact force or seating changes. Use the same view and contact method for every sample.

Record hook A and hook B separately: opening, position, orientation and transition condition. If operators disagree, repeat measurement on the same parts before adjusting the CNC program. A measurement disagreement is not evidence that the forming process has changed.

Validate final dimensions and function

After required processing, inspect the complete spring and carry out the specified load tests at the defined lengths. Confirm fit with the mating components or approved gauge where required. Dimensional conformity and force conformity are related requirements, but neither substitutes for the other.

Capture consecutive samples from startup and stable running, plus the agreed restart or changeover trial. Save the accepted program revision, tooling IDs, material record, measuring method and sample results. When comparing the spring making machine range, send this complete acceptance package to Jinchun so the proposal addresses finished spring requirements.

FAQ

1
Can a correct spring body still have unacceptable hooks?
Yes. Opening, orientation and transition geometry need separate inspection even when body dimensions are stable.
2
Should hooks be checked before or after heat treatment?
Check the stage specified for acceptance. Paired checks before and after required treatment can help identify where a change occurs.
3
Does a camless machine remove the need for hook tooling?
No. Independent motions still need suitable forming and supporting tools, clearance and a validated sequence.
prev
How to Design Welding Fixtures for Wire Frames and Mesh Panels
How to Control Squareness in CNC Wire Frame Bending and Welding
next
recommended for you
Get in touch with us

Foshan Jinchun is a technology-intensive industrial company specializing in the development of welding technology and equipment research and manufacturing, integrating scientific research, production and sales.

Contact Us
Address: No.25 Sanle Road, Beijiao Town, Shunde district, Foshan City, Guangdong Province, People's Republic of China 
Contact:  Charles
We chat:  18038626853
Copyright © 2026 Foshan Jinchun Industrial Automation Technology Co., Ltd. All Rights Reserved  www.jinchunmachine.com | XLC  | Sitemap  |  Privacy Policy
Contact us
phone
email
wechat
whatsapp
Contact customer service
Contact us
phone
email
wechat
whatsapp
cancel
Customer service